Datalink Systems i50 Especificações descarregar pdf (Página 47)

i50 Manual (5.10)

Page 47

www.datalinksystemsinc.com

Where the parameters are:

<MsgID> Message ID (0-16777215)

<UserID> User ID if addressed to a single DataHost/WebGate user. Not currently implemented,

and must be left blank or set to zero

<Subject> Email subject if message is an email

<Address> Email address if message is an email

<Message> Message body

<FileData> See section 11.3

<Error> “0”=Unknown command, “1”=No ID, “2”=Invalid ID, “3”=Unknown ID, “4”=Wrong

network for file transfer, “5”=File data too long

<Net> “0”=None, “1”=MSAT, “3”=Radio, “11”=Cellular, “12”=Globalstar, “14”=Iridium

<AlertState> “0”=Off, “3”=Cancelled, “5”=Active but silenced, “6”=Active

<AlertResp> “0” or “1”=Not acknowledged, “5”=ACK received

<RX> “0”=Receiver Idle, “1”=Receiving data

<TX> “0”=Transmitter Idle, “1”=Transmitting data

<Packets> Number of packets waiting to be sent

<Valid> “0”=No GPS data available, “1”=GPS Valid

<FixTime> Time of last GPS fix (sec since 12:00 am Dec 31, 1989 UTC)

<Fix> “0”=No GPS signal, “1”=GPS OK

<Lat> Latitude (degrees * 100000)

<Lon> Longitude (degrees * 100000)

<Heading> Heading (degrees)

<Speed> Speed (knots)

<Alt> Altitude (metres)

<Sats> Number of satellites visible

<HDOP> Horizontal accuracy

<Short> “0”=GPS antenna OK, “1”=GPS antenna short circuit

<SpdValid> “0”=Speed information invalid, “1”=Speed reading valid

<Motion> “0”=Device stationary, “1”=Device moving, “255”=Unknown

<IGN> “0”=IGN off, “1”=IGN on

<In1> “0”=Input 1 low, “1”=Input 1 high

<In2> “0”=Input 2 low, “1”=Input 1 high

<In3> “0”=Input 3 low, “1”=Input 1 high

<In4> “0”=Input 4 low, “1”=Input 1 high

<In5> “0”=ADC 1 low, “1”=ADC 1 high

<In6> “0”=ADC 1 low, “1”=ADC 2 high

<Out1> “0”=Output 1 low, “1”=Output 1 high

<Out2> “0”=Output 2 low, “1”=Output 2 high

<Out3> “0”=Output 3 low, “1”=Output 3 high

<Out4> “0”=Output 4 low, “1”=Output 4 high

<VOUT> “0”=VOUT off, “1”=VOUT on

<Temp> Internal temperature (degrees C * 100)

<ADC1> ADC 1 voltage (volts * 100)

<ADC2> ADC 2 voltage (volts * 100)

<Battery> Battery voltage (volts * 100)

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 64 65

Comentários a estes Manuais

Sem comentários

Datalink Systems i50 Especificações Página 47

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de navegação Datalink Systems i50